Time Now

Feb 13, 2015

Lathe Machine

lathe machine in machine manufacturing workshop banner

A lathe is a powered mechanical device in which the work is held and rotated against a suitable cutting tool for producing cylindrical forms in the metal, wood or any other suitable machinable material.


Principle of working


principle of working of lathe machine in machine manufacturing workshop

The principle of lathe machine is that it holds the work between two strong supports called as centers  or in a check or face plate which revolves. The chuck or the center is mounted on the main spindle of the machine. The cutting tool is rigidly supported in a tool port and it is fed against the rotating job. The job rotates in its axis and the tool is moved either parallel or to an inclination with its axis as such a cylindrical or tapered surface is produced.


Types of lathe

There are various types of lathe. They are as follows:
a. Precision lathe
b. Tool room lathe
c. Capstan and turret lathe
d. Automatic lathe
e. Speed lathe
f. Engine lathe
g. Bench lathe
h. Special purpose lathe



THE PRINCIPLE PARTS OF LATHE ARE DISCUSSED:


parts of lathe machine in machine manufacturing workshop having bed, head stock, tail stock, spindle, carriage, legs


Bed: 

The bed is the function of the lathe. It is supported on board box columns and is made of cast iron. It consist of two heavy metal slides running lengthwise with ways. Units which are mounted on the bed are the head-stock, the tail-stock and the carriage. Lathe bed is made of high grade special cast iron having high vibration damping qualities. It is secured rigidly over cabinet leg and leg. In its use care should be taken to avoid formation of scratches, nicks and dents by falling tools. It should be lubricated regularly.

Gap beds: 
Some beds have a gap just adjacent to the front of the head stock. It is gap beds. This type of bed can accommodate jobs which are bigger in diameter, but it is true for jobs of shorter length only.



Head stock: 

It supports the main spindle in the bearings and aligns it properly. It also houses necessary transmission mechanism with speed changing levers to obtain different speeds. Cone pulleys or gears could be used to change the speed of spindle. Holding devices which are mounted on head-stock spindle:


various head stocks chucks (three jaw chuck, four jaw chuck, face plate, collet chuck, magnetic shuck, lathe dog) in machine manufacturing workshop

a. Three jaw chuck
b. Four jaw chuck
c. Face plate
d. Collet chuck
e. Magnetic chuck
f. Lathe dog



Main spindle: 

It is a hollow cylindrical shaft and long cylindrical jobs can pass through the main spindle. The spin end facing the tail-stock is called the spindle nose. The spindle nose has a mores taper hole (self locking taper) and threads on outside. The mores taper is used to accommodate center or collet chuck or threaded portion of chuck.



Tail-stock: 

It is a movable part located opposite to head-stock on the ways of the bed. It is capable of sliding along the bed maintaining its alignment with head-stock. On medium size and smaller lathe it is moved along the bed manually, whereas in heavier lathes it is moved by hand wheel through a pinion that meshes with rack provided in front of lathe bed. It is used for four purposes:
a. To support free end during machining.
b. To hold tool for performing operations like drilling, reaming, tapping etc.
c. To center the job and the tool before any lathe operations.
d. To help in the operation of taper turning by tail stock set over method.



Carriage: 

It is located between head-stock and tail-stock. It can slide along bed guide ways and be locked at any position by tightening the carriage lock screws. It consist of following five main parts


a. APRON: 

It is fastened to saddle. It contains gears and clutches for transmitting motions from feed rod and hand wheel to the carriage. Also split nut which engages with the lead screws during threading. The clutch mechanism is used for transmitting motion from feed rod whereas the split nut along with the lead screw moves the carriage during thread cutting.


b. SADDLE: 

It is made up of H-shaped casting. It aids saddle to slide on bed guide ways by operating hand wheel. 


c. COMPOUND REST: 

It supports the tool post and cutting tool in its various positions. It may be swiveled on the cross-slide to any angle in the horizontal plane.


d. CROSS-SLIDE: 

It is provided with a female dovetail one side and assembled on top of saddle having a male dovetail.


e. TOOL POST: 

It is used to hold various tool holders and tools. Three types of tool post commonly used are:
• Ring and rocker tool post
• Square head tool post
• Quick change tool post



Legs: 

They are supports which carry entire load of the machine. Legs are casted and it is placed on the floor of the shop of foundation by grouting. The left leg acts as a housing for the motor, the pulleys and the counter shaft at the same time the right leg acts as a housing or the coolant tank, pump and the connecting pipes.




SPECIFICATION OF LATHE

The size of the lathe is specified by one of the following ways:
a. Length of the bed (Bed length will include head-stock)
b. Distance between centers (Maximum job length that can be held between centers)
c. Diameter of the work which can be turned between the ways (Maximum diameter that can be rotated)
d. Heights of centers
e. Swing over carriage


specification of lathe like its length, height, width, distance, diameter, swing over carriage in lathe machine workshop





OPERATIONS PERFORMED ON LATHE MACHINE


1. Facing
2. Rough Turning
3. Shouldering
4. Radius Turning
5. Necking
6. Taper turning
7. Thread cutting
8. Forming
9. Chamfering
10. Knurling
11. Drilling
12. Boring
13. Counter sinking
14. Counter boring

operations (facing, turning, shouldering, necking, cutting, forming, chamfering, knurling, drilling, boring, counter sinking) with the help of lathe machine



DIFFERENT METHODS OF TAPER TURNING

Compound rest method: 


compound rest method in taper turning attachment in lathe machine workshop

Compound rest method is used for turning steeps and short tapers. It is having a circular base graduated in degree. When taper of required degrees is turned, the base of compound rest is swiveled through an angle equal to half of the taper angle.





Tapper turning attachment: 

taper turning attachment in lathe machine workshop
It is bolted on the back of the lathe and has a guide bar which may be set at the desired angle of taper. As the carriage moves along the bed length, a slide over the bar causes the tool to move in and out according to the setting of the bar. Lathe center remains aligned and same taper can be given on various jobs.




Form tool method: 




When the length of the taper is very short it can be turned by a bored nosed tool consisting of cutting edge half the taper angle. While using this type of tool lot of chattering is there, as such this type of tool is used specially when the machine have a very rigid base.

Shaper Machine


shaper machine used for planning surface of metal in machine manufacturing workshop


Shaper is a versatile machine which is primarily intended for producing flat surfaces. These surfaces may be horizontal, vertical or inclined. This machine involves the use of single point cutting tool held in a properly designed tool box mounted on a reciprocating ram.


WORKING PRINCIPLE

working principle of shaper machine manufacturing workshop
In shaper the job is rigidly held in machine vice. Tool is held in the tool post mounted on ram. This ram reciprocates to and fro and so the cutting of the material takes place in the forward stroke of ram and return stroke is ideal. The job is given index feed normal to the line of action of cutting tool. Principle parts of the shaper are:




COLUMN: 


column (part of shaper) working principle of shaper in machine manufacturing workshop



It is a hollow structure consisting of two vertical walls and cast from cast iron. It is a rigid structure, gives support to the ram and is supported by the base. The cross rail carries table and table is derived in front of column. In one of two vertical walls, a hole is made to inspect the driving mechanism of the ram located in it.





BASE: 

It supports the whole machine and is bolted to the floor with the help of foundation bolts.

CROSS-RAIL: 

It is a box like structure over which the saddle slides horizontally. The cross rail is maintained accurately to the column. The table cross feed screw and the cross rail vertical feed are housed inside it.

SADDLE AND TABLE: 

The table is bolted on the saddle and the table is capable of moving in horizontal and vertical direction. It can be fitted in inclined position also. The job is supported on the table with the help of vice or some simple fixture. The table is provided with T-slots for clamping vice, fixture is and other tooling in it. Shaper ribs are provided: 
a. To adjust the saddle on the cross rail.
b. To adjust the ram on the column.
c. To adjust the tool slide on the swivel head plate.

SHAPER HEAD: 

It is fastened firmly to the front of the ram and consists of tool slide, tool post and clapper box. The head can be swiveled at any angle, tool is vertically fed by the vertical tool feed screw. The tool holder is fitted in the clapper which is fitted on the clapper box. Clapper block is free to pivot forward. The tool swings up on the return stroke otherwise work surface is likely to badly gauged and the tool quickly damaged by wear. Vertical feed is measured by micrometer dial near the handle.

RAM: 

Ram is a reciprocating member and it carries shaper head in the front, on which the cutting tool is mounted. It slides in the guide ways made on the top of the column. It should be designed as rigid as possible. A mechanism is provided inside the ram to change its position relative to the job.

POWER TRANSMISSION: 

The power to the shaper is transmitted from an electric motor through V-belt drive. The gears may be shifted by the speed change levers, large gear is the shaper is called bull gear or crank gear.


SPECIFICATION OF THE SHAPER


specification of shaper machine in manufacturing workshop


Shaper is specified by following parameters:
a. Maximum length of stroke
b. Table top (length*width) 
c. Table horizontal travel
d. Table vertical travel
e. Tool box-vertical travel
f. Number and range of speed obtained
g. Number and range of feeds
h. Swivel base, vise, width and depth of jaw
i. Swivel base
j. Size of tool
k. Speed of motor





FEED MECHANISM


feed mechanism and quick return mechanism in shaper machine workshop
Down feed and cross feed movements can be given at the end of the return stroke only by the automatic feed mechanism. The bull gear rotates driving disc. As the disc rotated through half of the revolution, the top of the rocking arm now moves in anti-clockwise direction only and the straight side of the pawl engages with the teeth of the ratchet wheel to move in anticlockwise direction only. As the driving disc is connected to the bull gear the table feed movement is affected when the bull gear or the driving disc rotates through half of the revolution. Rotating through other half imparts no feed movement. To reverse the direction of rotation and feed a knob at the top of the pawl is rotated through 1800 after removing the pin. The amount of feed may be altered by increasing the eccentrically at the driving disc.


SHAPER OPERATIONS

Horizontal flat surface machining: 


horizontal flat surface machining shaper operation in manufacturing workshop




This is achieved by moving table under the tool. Automatic feed can be given or manual table is moved at the end of the return stroke. Length of the stroke should be 20mm longer than the job. Depth should be 1.5-3.0mm.






Vertical surface machining: 

Vertical feed is given to the tool by rotating the down feed screw by hand. It should be 0.25mm at the end of the return stroke.

Machining angular surface: 

The vertical slide of the tool head is swivelled to the required angle in either direction. The down feed is given by rotating the down feed screw.

Cutting slots and keyways: 

For cutting slots or keyways a square nose tool similar to a parting tool is selected. External keyways are cut on a shaft by firs drilling a hole at the blind end of keyways.

Irregular surface: 

Shaper can produce a convex or concave surface or a combination of the above surface by a forming tool. If the curve is sufficiently large, power cross-feed in conjugation with manual down feed is so adjusted that the tool will trace the required centre.

Machining splines or Cutting gears: 

By using the indexing mechanism, or index table a gear or equally spaced spline may be cut.

Machine Shop

Machine manufacturing workshop used in machines shop



The shop where most of the work is performed on different machines is called machine shop. In Machine shop, the raw material is cut, machined, formed or shaped with the help of machines. Different machines used in machine shop are:

1. Lathe machine
2. Shaper
3. Milling machine
4. Planning machine
5. Drilling machine
6. Grinding machine
7. Threading machine

Wood working Processes



wood working process in carpentry workshop

marking and measuring process in capentry

Marking and measuring:

Before starting any process first of all the job is measured by various measuring tools and then it is marked properly. This helps in avoiding frequent measurements on the job while processing. Care must be taken to measure the dimension accurately by the instruments as per the drawing. Initially the marking is done then after planning again the marking is done.



sawing operation in carpentry process


Sawing:

It is done for cutting the raw material for a given size and removing the extra material. Selection of the type of saw is decided by type of operation to be performed on the job. Cutting should be started from the tip of the saw and followed by the entire length of the saw.



planning process in carpentry


Planning:

This operation is performed on the wood to smooth the surface of the wood. Initially a jack plane is applied followed by trying plane for smoothing and finishing. Selection of the rest of the plane is made base on specific operation.



mortising and tennoning operation in carpentry process



Mortising and tenoning:

Mortise is in the form of a cavity that forms the female part and the tenon the projection on the other part that is a male part and both of them are fitted to form the mortise and tenon joint. For producing the tenon part the tenon saw is used and for the mortise the firmer and the mortise chisel is used.





boring process in capentry



Boring:

This is an operation of producing circular holes in the wooden work piece. First the center of the hole is located and then the hole is drilled by the bits for desired size and depth.




molding operation in carpentry process


Molding:

This process is used for producing the wooden items that are used for decoration and that is done by special plane called as molding plane.




tongueing and grooving operation in carpentry process


Tonguing and grooving:

In case when the desired planks are very wide for examples specially while making the tables and the enclosure. The commercial planks are taken and they are joined by this joint in order to get the desired width.






rebating operation in carpentry process



Rebating:

This process is  used for producing a step along the edge of a plank, either longitudinal or cross.









JOINTS

To connect together the different parts of wood in a proper manner is known as joining. And the shape formed is known as a joint. Types of joints are:
lengthening joint in carpentry




Lengthening joints





widening joint in carpentry




Widening joints






framing joint in carpentry






Framing joints









box joint in carpentry






Box joints








circular joint in carpentry






Circular joints